Does MWRA water contain lead?
MWRA water is lead-free when it leaves the reservoirs. MWRA and local distribution pipes that carry the water to your community are made mostly of iron and steel, and do not add lead to water. However, lead can get into tap water through a lead service line connecting your house to the pipe in the street, or pipes in the home, lead solder used in plumbing, and some brass fixtures. Corrosion or wearing away of lead based materials can add lead to tap water, especially if water sits for a long time in the pipes before use.
More about Lead in Drinking Water
Do faucets contain lead?
Most faucets purchased prior to 1997 were constructed of brass or chrome-plated brass, which contain up to 8 percent lead (the main metals in brass are copper and zinc). Water sitting for several hours or overnight in a brass faucet can leach lead from the brass faucet interior which may produce high lead levels in the first draw of drinking water. Later regulations mandated that most faucets purchased after 1997 contain less lead than previously used thereby reducing the possible leaching of lead. However, the most recent legislation, called “Get the Lead Out,” mandates that after January 4, 2014, all faucets purchased will contain no more than a weighted average of 0.25 percent lead in relation to wetted surface.
How can I tell if my faucet is "lead free"?
Responding to recent regulations, faucet manufacturers have decreased or eliminated the lead in residential kitchen faucets, bathroom faucets, bar faucets, drinking fountains, and icemakers. Starting January 4, 2014, all faucets will be produced with no more than a weighted average of 0.25 percent lead with respect to the wetted surface. The national standard for certifying plumbing fixtures "lead free" status is determined by the National Sanitary Foundation (NSF) - the standard is International Standard 61-Section 9. New faucets meeting the NSF 61 standard will have NSF 61/9 stamped on the new faucet’s cardboard box. For more information on lead-free fixtures including catalogs and website directories, contact NSF at 1-800-NSF-MARK or www.nsf.org.
Are there any faucets with no lead at all?
Some faucet manufactures produce plastic faucets that have virtually zero lead. Other manufactures are substituting other metals for the lead in the brass, inserting copper tubes inside the brass faucets, or applying special coatings on the inside of the faucets in order to minimize or eliminate lead leaching. With the recent legislation, more and more faucet manufacturers are advertising faucets that adhere to the new “lead-free” definition allowing a maximum of 0.25 percent lead.
Does it really matter if I have an ultra-low lead faucet?
In extreme cases, older faucets can contribute up to one-third of the lead in water that has been sitting in the pipes for several hours, with the remainder coming from other plumbing such as pre-1988 lead solder joints in copper pipes or a lead service line. Residents who let the water run at the tap in the morning for one minute and use cold water for cooking should have little concern with respect to lead in the drinking water. If residents are still concerned, they can have their water tested.
Do some new plumbing fixtures still contain lead?
Federal and State lead regulations do not cover any pipes, pipe fittings, plumbing fittings, or fixtures, that are used exclusively for nonpotable services like manufacturing, industrial processing, irrigation, outdoor watering, or other uses where the water is not anticipated to be used for human consumption. This includes toilets, bidets, urinals, fill valves, flushometer valves, tub fillers, shower valves, service saddles, or water distribution main gate valves that are two inches in diameter or larger.
Federal and State lead regulations also do not cover hose bibs, bathtub fixtures, shower heads, and industrial faucets.
Be sure that only valves and filters intended for drinking water supply are used in any home plumbing project.
Is drinking water the main source of lead exposure?
Lead contamination from lead-based paint, dirt, and dust accounts for most of the exposure. Lead from drinking water can make up to 20 percent of a person’s total exposure to lead.
The most cost effective ways to minimize lead exposure from drinking water are:
- flush the kitchen faucet for one minute in the morning or after coming home from school/work
- use only cold water for drinking and cooking
- get your water tested.
How do I get information about lead in my drinking water?
The Massachusetts Department of Public Health (DPH) has information on childhood lead poisoning prevention through the Massachusetts DPH Lead Exposure Office at (617) 284-8400 or its website.
The NSF certifies plumbing fixtures, water filters, and bottled water and can be reached at 1-800-NSF-MARK or through their website at www.nsf.org.
The Environmental Protection Agency (EPA) operates a National Lead Information Center and can be reached at 1-800-424-LEAD or through its website.
About Lead Service Lines